Detailed Explanation Of The Production Process Of Spring Hangers

Apr 30, 2025

Leave a message

1. Material preparation

     The core materials for making spring hangers include hanger body, springs, connectors and surface treatment materials. The hanger body is made of Q235 carbon steel plate. According to different load requirements, the thickness of the steel plate is selected between 5-10mm; the spring is made of 60Si2Mn spring steel with a diameter range of φ12-φ30mm, which must comply with GB/T 1222 standards; the connectors use 45 steel bolts and nuts with a performance level of 8.8 or above; the surface treatment materials are epoxy zinc-rich primer and acrylic topcoat to improve corrosion resistance.

2. Processing technology

2.1 Processing of the hanger body

     First, the Q235 steel plate is cut into the hanger body and the connecting plate according to the design drawings by a CNC laser cutting machine, and the dimensional tolerance is strictly controlled within ±0.5mm. After cutting, the plate is bent 90° or 180° by a CNC bending machine to form the hanger support arm and the mounting ear. The bending radius must comply with the JB/T 18276 standard. Finally, the connecting plate and the support arm are welded by carbon dioxide gas shielded welding (GMAW) to ensure that the weld height is not less than 70% of the parent material thickness. Ultrasonic flaw detection (UT) testing is also required after welding to ensure welding quality.

2.2 Spring processing

     The 60Si2Mn spring steel bar is wound into a spiral spring by a CNC spring winding machine. During the winding process, the pitch error is strictly controlled to be ±1mm, and the free height tolerance is ±2mm. The rolled spring needs to be heat treated and placed in a box-type resistance furnace. It is quenched at 860℃ and tempered at 420℃ to make the surface hardness reach HRC42-48, and Rockwell hardness test (HR) is performed. In order to enhance the corrosion resistance and durability of the spring, it is also necessary to perform shot peening treatment, and then spray epoxy zinc-based anti-corrosion coating with a thickness of ≥80μm.

2.3 Connection processing

     Bolts and nuts are made by cold heading forming process, and the thread accuracy meets the GB/T 197-6g standard. The surface is galvanized with a coating thickness of ≥8μm to improve the strength and corrosion resistance of the connection.

3. Assembly and debugging

     First, insert the spring into the spring sleeve of the hanger body, and use bolts to initially fix the upper and lower connecting plates to ensure that the spring is vertically centered. Then, a rated load of 1000N-5000N is applied to the spring hanger through a tensile testing machine, and the spring compression is measured, with an error of ≤±2% of the rated stroke. After qualified debugging, tighten all bolts and apply anti-loosening glue, and finally install the dust cover to prevent debris from entering the spring gap and affecting the performance of the hanger.

4. Quality Inspection

     Quality inspection is the key link to ensure the qualification of spring hangers. During the appearance inspection, it is necessary to ensure that there are no cracks or deformations on the surface, the coating is uniform and there is no missing coating, and there is no slag inclusion or 2.3 Connection processing.

Bolts and nuts are made by cold heading forming process, and the thread accuracy meets the GB/T 197-6g standard. The surface is galvanized with a coating thickness of ≥8μm to improve the strength and corrosion resistance of the connection pores in the weld, refer to the GB/T 3323 standard. When performing the load test, apply 1.5 times the rated load to the hanger for 30 minutes, and no permanent deformation is required, which meets the JB/T 8130.1 standard. In addition, the surface coating needs to be subjected to a 1000-hour neutral salt spray test (NSS), and the corrosion level must be ≥9, refer to the GB/T 10125 standard.

V. Finished product delivery

     The finished product is packed in moisture-proof cartons, and the interior is filled with pearl cotton to prevent damage during transportation. At the same time, accessories such as installation instructions and inspection reports are placed in the box. The product label will indicate the model (such as TH3 - 1000), rated load, implementation standard (JB/T 8130.2) and production date, which is convenient for users to identify and use.

     Through the above rigorous production process, the spring hanger produced can meet the high-precision shock absorption and load-bearing requirements in multiple fields such as petrochemicals, electricity, and construction, providing reliable protection for the safe and stable operation of various projects.

 

Send Inquiry